hd02 thru hd10 single phase glass passivated bridge rectifiers voltage range - 200 to 1000 volts current - 0.5/0.8 ampere case : molded plastic body terminals : plated leads solderable per mil-std-750, method 2026 polarity : polarity symbols marked on case mounting position : any weight :0.008 ounce, 0.22 grams features mechanical data dimensions in inches and (millimeters) maximum ratings and electrical characteristics 15 75 -55 to +150 -55 to +150 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 hd02 0.5 0.8 notes:1.on glass epoxy p.c.b. mounted on 0.05x0.05''(1.3x1.3mm) pads 2.on aluminum substrate p.c.b. with on area of 0.8''x0.8''(20x20mm) mounted on 0.05x0.05''(1.3x1.3mm) solder pad 3.measured at 1.0mhz and applied reverse voltage of 4.0 volts. ideal for printed circuit board reliable low cost construction utilizing molded plastic technique high temperature soldering guaranteed: 260 / 10 seconds at 5 lbs., (2.3kg) tension small size, simple installation high surge current capability ratings at 25 ambient temperature unless otherwise specified. single phase half-wave 60hz,resistive or inductive load, for capacitive load derate current by 20%. volts volts volts symbols units amps amps volts v rrm v rms v dc i f(av) i fsm maximum repetitive peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current at t c =30 on glass-epoxy p.c.b. on aluminum substrate peak forward surge current, 8.3ms single half sine-wave superimposed on rated load (jedec method) maximum instantaneous forward voltage drop per leg at 0.4a maximum dc reverse current t a =25 at rated dc blocking voltage t a =125 typical junction capactiance per leg(note3) typical thermal resistance per leg operating temperature range storage temperature range c j r ja t j t stg i r v f ua ua 1.0 30 5.0 500 hds HD06 hd04 hd08 hd10 pf /w + .193(4.90) .177(4.50) .157(4.00) .142(3.60) .276(7.0) max .102(2.60) .087(2.20) .033(0.84) .022(0.56) .118(3.0) max .106(2.70) .090(2.30) .008(0.20) max .053(1.53) .037(0.95) .083(2.12) .043(1.10) .043(1.10) .028(0.70) .014(0.35) .006(0.15) mdd catalog number
35 30 25 20 15 10 5 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.1 1 10 100 200 reverse voltage.(v) fig. 3-typical forward voltage characteristics per leg number of cycles fig. 2-maximum non-repetitive peak forward surge current perleg fig. 1- derating curve output rectified current for average forward rectified current(a) instantaneous forward current(a) junction capacitance.(pf) peak forward surge current.(a) instantaneous forward voltage .(v) 1 100 10 1 0.1 0.01 30 25 20 15 10 5 0 0 20 40 60 80 100 1 0 0 10 1 0.1 0.01 percent of rated peak reverse voltage(%) fig. 4-typical reverse leakage characteristics per leg instantaneous reverse leakage current.(ua) ambient temperature,( ) 10 fig. 5-typical junction capactitane per leg ta=40 single half sine-wave (jedec method) 1cycle f=50hz f=60hz t j =25 pulse width=300 u s 1% duty cycle t j =125 t j =25 t j =25 f=1.0mh z vsig=50mv p-p 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 20 40 60 80 100 120 140 160 glass epoxy p.c.b. aluminum substrate ratings and characteristic curves hd02 thru hd10 the cruve g ra p h is for reference onl y , can't be the basis for j ud g ment ( ? ) !
|
